- Devise and construct tools, dies, molds, jigs, and fixtures, or modify existing tools and equipment.
Occupations with related tasks Save Table: XLSX CSV
Closely Related Tasks | All Related Tasks | Job Zone | Code | Occupation |
4 | 4 | 2 | 51-4071.00 | Foundry Mold and Coremakers |
3 | 4 | 2 | 51-9195.00 | Molders, Shapers, and Casters, Except Metal and Plastic |
3 | 3 | 3 | 51-4111.00 | Tool and Die Makers |
3 | 3 | 2 | 51-4072.00 | Molding, Coremaking, and Casting Machine Setters, Operators, and Tenders, Metal and Plastic |
2 | 4 | 3 | 51-7031.00 | Model Makers, Wood |
2 | 3 | 3 | 51-4041.00 | Machinists |
2 | 2 | 3 | 51-9071.00 | Jewelers and Precious Stone and Metal Workers |
1 | 3 | 3 | 51-7032.00 | Patternmakers, Wood |
1 | 3 | 2 | 51-4122.00 | Welding, Soldering, and Brazing Machine Setters, Operators, and Tenders |
1 | 1 | 2 | 51-2051.00 | Fiberglass Laminators and Fabricators |
1 | 1 | 2 | 51-4194.00 | Tool Grinders, Filers, and Sharpeners |
1 | 1 | 2 | 51-9012.00 | Separating, Filtering, Clarifying, Precipitating, and Still Machine Setters, Operators, and Tenders |
- Position cores into lower sections of molds, and reassemble molds for pouring.
- Form and assemble slab cores around patterns, and position wire in mold sections to reinforce molds, using hand tools and glue.
- Tend machines that bond cope and drag together to form completed shell molds.
- Rotate sweep boards around spindles to make symmetrical molds for convex impressions.
- Clean and smooth molds, cores, and core boxes, and repair surface imperfections.
- Sift and pack sand into mold sections, core boxes, and pattern contours, using hand or pneumatic ramming tools.
- Position patterns inside mold sections, and clamp sections together.
- Sprinkle or spray parting agents onto patterns and mold sections to facilitate removal of patterns from molds.
- Move and position workpieces, such as mold sections, patterns, and bottom boards, using cranes, or signal others to move workpieces.
- Lift upper mold sections from lower sections, and remove molded patterns.
- Cut spouts, runner holes, and sprue holes into molds.
- Pour molten metal into molds, manually or with crane ladles.
- Operate ovens or furnaces to bake cores or to melt, skim, and flux metal.
- Position cores into lower sections of molds, and reassemble molds for pouring.
- Form and assemble slab cores around patterns, and position wire in mold sections to reinforce molds, using hand tools and glue.
- Tend machines that bond cope and drag together to form completed shell molds.
- Rotate sweep boards around spindles to make symmetrical molds for convex impressions.
- Assemble, insert, and adjust wires, tubes, cores, fittings, rods, or patterns into molds, using hand tools and depth gauges.
- Operate molding machines that compact sand in flasks to form molds.
- Construct or form molds for use in casting clay or plaster objects, using plaster, fiberglass, rubber, casting machines, patterns, or flasks.
- Align and assemble parts to produce completed products, using gauges and hand tools.
- Read work orders or examine parts to determine parts or sections of products to be produced.
- Trim or remove excess material, using scrapers, knives, or band saws.
- Brush or spray mold surfaces with parting agents or insert paper into molds to ensure smoothness and prevent sticking or seepage.
- Engrave or stamp identifying symbols, letters, or numbers on products.
- Clean, finish, and lubricate molds and mold parts.
- Separate models or patterns from molds and examine products for accuracy.
- Set the proper operating temperature for each casting.
- Load or stack filled molds in ovens, dryers, or curing boxes, or on storage racks or carts.
- Operate and adjust controls of heating equipment to melt material or to cure, dry, or bake filled molds.
- Select sizes and types of molds according to instructions.
- Patch broken edges or fractures, using clay or plaster.
- Withdraw cores or other loose mold members after castings solidify.
- Repair mold defects, such as cracks or broken edges, using patterns, mold boxes, or hand tools.
- Measure and cut products to specified dimensions, using measuring and cutting instruments.
- Smooth surfaces of molds, using scraping tools or sandpaper.
- Measure ingredients and mix molding, casting material, or sealing compounds to prescribed consistencies, according to formulas.
- Remove excess materials and level and smooth wet mold mixtures.
- Place forms around models and separately immerse each half portion of a model in plaster, wax, or other mold-making materials.
- Verify dimensions of products, using measuring instruments, such as calipers, vernier gauges, or protractors.
- Bore holes or cut grates, risers, or pouring spouts in molds, using power tools.
- Locate and scribe parting lines on patterns, using measuring instruments, such as calipers, squares, or depth gauges.
- Tap or tilt molds to ensure uniform distribution of materials.
- Pour, pack, spread, or press plaster, concrete, or other materials into or around models or molds.
- Assemble, insert, and adjust wires, tubes, cores, fittings, rods, or patterns into molds, using hand tools and depth gauges.
- Operate molding machines that compact sand in flasks to form molds.
- Construct or form molds for use in casting clay or plaster objects, using plaster, fiberglass, rubber, casting machines, patterns, or flasks.
- Align and assemble parts to produce completed products, using gauges and hand tools.
- Fit and assemble parts to make, repair, or modify dies, jigs, gauges, and tools, using machine tools, hand tools, or welders.
- Design jigs, fixtures, and templates for use as work aids in the fabrication of parts or products.
- Develop and design new tools and dies, using computer-aided design software.
- Verify dimensions, alignments, and clearances of finished parts for conformance to specifications, using measuring instruments such as calipers, gauge blocks, micrometers, or dial indicators.
- Set up and operate conventional or computer numerically controlled machine tools such as lathes, milling machines, or grinders to cut, bore, grind, or otherwise shape parts to prescribed dimensions and finishes.
- Visualize and compute dimensions, sizes, shapes, and tolerances of assemblies, based on specifications.
- Study blueprints, sketches, models, or specifications to plan sequences of operations for fabricating tools, dies, or assemblies.
- Inspect finished dies for smoothness, contour conformity, and defects.
- Select metals to be used from a range of metals and alloys, based on properties such as hardness or heat tolerance.
- Lift, position, and secure machined parts on surface plates or worktables, using hoists, vises, v-blocks, or angle plates.
- File, grind, shim, and adjust different parts to properly fit them together.
- Smooth and polish flat and contoured surfaces of parts or tools, using scrapers, abrasive stones, files, emery cloths, or power grinders.
- Measure, mark, and scribe metal or plastic stock to lay out machining, using instruments such as protractors, micrometers, scribes, or rulers.
- Conduct test runs with completed tools or dies to ensure that parts meet specifications, making adjustments as necessary.
- Cut, shape, and trim blanks or blocks to specified lengths or shapes, using power saws, power shears, rules, and hand tools.
- Set up and operate drill presses to drill and tap holes in parts for assembly.
- Set pyrometer controls of heat-treating furnaces and feed or place parts, tools, or assemblies into furnaces to harden.
- Fit and assemble parts to make, repair, or modify dies, jigs, gauges, and tools, using machine tools, hand tools, or welders.
- Design jigs, fixtures, and templates for use as work aids in the fabrication of parts or products.
- Develop and design new tools and dies, using computer-aided design software.
- Clamp metal and plywood strips around dies or patterns to form molds.
- Shape molds to specified contours, using sand, and trowels and related tools.
- Assemble shell halves, patterns, and foundry flasks, and reinforce core boxes, using glue, clamps, wire, bolts, rams, or machines.
- Measure and visually inspect products for surface and dimension defects to ensure conformance to specifications, using precision measuring instruments.
- Observe continuous operation of automatic machines to ensure that products meet specifications and to detect jams or malfunctions, making adjustments as necessary.
- Set up, operate, or tend metal or plastic molding, casting, or coremaking machines to mold or cast metal or thermoplastic parts or products.
- Turn valves and dials of machines to regulate pressure, temperature, and speed and feed rates, and to set cycle times.
- Read specifications, blueprints, and work orders to determine setups, temperatures, and time settings required to mold, form, or cast plastic materials, as well as to plan production sequences.
- Observe meters and gauges to verify and record temperatures, pressures, and press-cycle times.
- Connect water hoses to cooling systems of dies, using hand tools.
- Remove parts, such as dies, from machines after production runs are finished.
- Perform maintenance work such as cleaning and oiling machines.
- Smooth and clean inner surfaces of molds, using brushes, scrapers, air hoses, or grinding wheels, and fill imperfections with refractory material.
- Operate hoists to position dies or patterns on foundry floors.
- Cool products after processing to prevent distortion.
- Install dies onto machines or presses and coat dies with parting agents, according to work order specifications.
- Unload finished products from conveyor belts, pack them in containers, and place containers in warehouses.
- Remove finished or cured products from dies or molds, using hand tools, air hoses, and other equipment, stamping identifying information on products when necessary.
- Obtain and move specified patterns to work stations, manually or using hoists, and secure patterns to machines, using wrenches.
- Select and install blades, tools, or other attachments for each operation.
- Repair or replace damaged molds, pipes, belts, chains, or other equipment, using hand tools, hand-powered presses, or jib cranes.
- Inventory and record quantities of materials and finished products, requisitioning additional supplies as necessary.
- Select coolants and lubricants, and start their flow.
- Adjust equipment and workpiece holding fixtures, such as mold frames, tubs, and cutting tables, to ensure proper functioning.
- Maintain inventories of materials.
- Position and secure workpieces on machines, and start feeding mechanisms.
- Trim excess material from parts, using knives, and grind scrap plastic into powder for reuse.
- Mix and measure compounds, or weigh premixed compounds, and dump them into machine tubs, cavities, or molds.
- Spray, smoke, or coat molds with compounds to lubricate or insulate molds, using acetylene torches or sprayers.
- Preheat tools, dies, plastic materials, or patterns, using blowtorches or other equipment.
- Pour or load metal or sand into melting pots, furnaces, molds, or hoppers, using shovels, ladles, or machines.
- Pull level and toggle latches to fill molds, to regulate tension on sheeting, and to release mold covers.
- Skim or pour dross, slag, or impurities from molten metal, using ladles, rakes, hoes, spatulas, or spoons.
- Clamp metal and plywood strips around dies or patterns to form molds.
- Shape molds to specified contours, using sand, and trowels and related tools.
- Assemble shell halves, patterns, and foundry flasks, and reinforce core boxes, using glue, clamps, wire, bolts, rams, or machines.
- Construct wooden models, patterns, templates, full scale mock-ups, and molds for parts of products and production tools.
- Build jigs that can be used as guides for assembling oversized or special types of box shooks.
- Fit, fasten, and assemble wood parts together to form patterns, models, or sections, using glue, nails, dowels, bolts, screws, and other fasteners.
- Fabricate work aids such as scrapers or templates.
- Verify dimensions and contours of models during hand-forming processes, using templates and measuring devices.
- Read blueprints, drawings, or written specifications, and consult with designers to determine sizes and shapes of patterns and required machine setups.
- Set up, operate, and adjust a variety of woodworking machines such as bandsaws and planers to cut and shape sections, parts, and patterns, according to specifications.
- Trim, smooth, and shape surfaces, and plane, shave, file, scrape, and sand models to attain specified shapes, using hand tools.
- Select wooden stock, determine layouts, and mark layouts of parts on stock, using precision equipment such as scribers, squares, and protractors.
- Mark identifying information on patterns, parts, and templates to indicate assembly methods and details.
- Plan, lay out, and draw outlines of units, sectional patterns, or full-scale mock-ups of products.
- Maintain pattern records for reference.
- Issue patterns to designated machine operators.
- Finish patterns or models with protective or decorative coatings such as shellac, lacquer, or wax.
- Construct wooden models, patterns, templates, full scale mock-ups, and molds for parts of products and production tools.
- Build jigs that can be used as guides for assembling oversized or special types of box shooks.
- Fit, fasten, and assemble wood parts together to form patterns, models, or sections, using glue, nails, dowels, bolts, screws, and other fasteners.
- Fabricate work aids such as scrapers or templates.
- Fit and assemble parts to make or repair machine tools.
- Design fixtures, tooling, or experimental parts to meet special engineering needs.
- Install experimental parts or assemblies, such as hydraulic systems, electrical wiring, lubricants, or batteries into machines or mechanisms.
- Calculate dimensions or tolerances, using instruments, such as micrometers or vernier calipers.
- Machine parts to specifications, using machine tools, such as lathes, milling machines, shapers, or grinders.
- Measure, examine, or test completed units to check for defects and ensure conformance to specifications, using precision instruments, such as micrometers.
- Set up, adjust, or operate basic or specialized machine tools used to perform precision machining operations.
- Program computers or electronic instruments, such as numerically controlled machine tools.
- Study sample parts, blueprints, drawings, or engineering information to determine methods or sequences of operations needed to fabricate products.
- Monitor the feed and speed of machines during the machining process.
- Maintain machine tools in proper operational condition.
- Align and secure holding fixtures, cutting tools, attachments, accessories, or materials onto machines.
- Confer with numerical control programmers to check and ensure that new programs or machinery will function properly and that output will meet specifications.
- Operate equipment to verify operational efficiency.
- Evaluate machining procedures and recommend changes or modifications for improved efficiency or adaptability.
- Diagnose machine tool malfunctions to determine need for adjustments or repairs.
- Dispose of scrap or waste material in accordance with company policies and environmental regulations.
- Confer with engineering, supervisory, or manufacturing personnel to exchange technical information.
- Lay out, measure, and mark metal stock to display placement of cuts.
- Separate scrap waste and related materials for reuse, recycling, or disposal.
- Check work pieces to ensure that they are properly lubricated or cooled.
- Support metalworking projects from planning and fabrication through assembly, inspection, and testing, using knowledge of machine functions, metal properties, and mathematics.
- Install repaired parts into equipment or install new equipment.
- Dismantle machines or equipment, using hand tools or power tools to examine parts for defects and replace defective parts where needed.
- Test experimental models under simulated operating conditions, for purposes such as development, standardization, or feasibility of design.
- Set up or operate metalworking, brazing, heat-treating, welding, or cutting equipment.
- Prepare working sketches for the illustration of product appearance.
- Establish work procedures for fabricating new structural products, using a variety of metalworking machines.
- Advise clients about the materials being used for finished products.
- Fit and assemble parts to make or repair machine tools.
- Design fixtures, tooling, or experimental parts to meet special engineering needs.
- Install experimental parts or assemblies, such as hydraulic systems, electrical wiring, lubricants, or batteries into machines or mechanisms.
- Construct preliminary models of wax, metal, clay, or plaster, and form sample castings in molds.
- Design and fabricate molds, models, and machine accessories, and modify hand tools used to cast metal and jewelry pieces.
- Position stones and metal pieces, and set, mount, and secure items in place, using setting and hand tools.
- Smooth soldered joints and rough spots, using hand files and emery paper, and polish smoothed areas with polishing wheels or buffing wire.
- Create jewelry from materials such as gold, silver, platinum, and precious or semiprecious stones.
- Make repairs, such as enlarging or reducing ring sizes, soldering pieces of jewelry together, and replacing broken clasps and mountings.
- Clean and polish metal items and jewelry pieces, using jewelers' tools, polishing wheels, and chemical baths.
- Cut and file pieces of jewelry such as rings, brooches, bracelets, and lockets.
- Select and acquire metals and gems for designs.
- Compute costs of labor and materials to determine production costs of products and articles.
- Examine assembled or finished products to ensure conformance to specifications, using magnifying glasses or precision measuring instruments.
- Pierce and cut open designs in ornamentation, using hand drills and scroll saws.
- Pour molten metal alloys or other materials into molds to cast models of jewelry.
- Shape and straighten damaged or twisted articles by hand or using pliers.
- Soften metal to be used in designs by heating it with a gas torch and shape it, using hammers and dies.
- Determine appraised values of diamonds and other gemstones based on price guides, market fluctuations, and stone grades and rarity.
- Grade stones based on their color, perfection, and quality of cut.
- Plate articles such as jewelry pieces and watch dials, using silver, gold, nickel, or other metals.
- Write or modify design specifications such as the metal contents and weights of items.
- Create new jewelry designs and modify existing designs, using computers as necessary.
- Buy and sell jewelry, or serve as agents between buyers and sellers.
- Record the weights and processing times of finished pieces.
- Lay out designs on metal stock, and cut along markings to fabricate pieces used to cast metal molds.
- Mark, engrave, or emboss designs on metal pieces such as castings, wire, or jewelry, following specifications.
- Cut designs in molds or other materials to be used as models in the fabrication of metal and jewelry products.
- Research and analyze reference materials, and consult with interested parties to develop new products or modify existing designs.
- Anneal precious metal objects such as coffeepots, tea sets, and trays in gas ovens for prescribed times to soften metal for reworking.
- Weigh, mix, and melt metal alloys or materials needed for jewelry models.
- Rotate molds to distribute alloys and to prevent formation of air pockets.
- Rout out locations where parts are to be joined to items, using routing machines.
- Construct preliminary models of wax, metal, clay, or plaster, and form sample castings in molds.
- Design and fabricate molds, models, and machine accessories, and modify hand tools used to cast metal and jewelry pieces.
- Construct wooden models, templates, full scale mock-ups, jigs, or molds for shaping parts of products.
- Fit, fasten, and assemble wood parts together to form patterns, models, or sections, using glue, nails, dowels, bolts, and screws.
- Glue fillets along interior angles of patterns.
- Read blueprints, drawings, or written specifications to determine sizes and shapes of patterns and required machine setups.
- Lay out patterns on wood stock and draw outlines of units, sectional patterns, or full-scale mock-ups of products, based on blueprint specifications and sketches, and using marking and measuring devices.
- Trim, smooth, and shape surfaces, and plane, shave, file, scrape, and sand models to attain specified shapes, using hand tools.
- Divide patterns into sections according to shapes of castings to facilitate removal of patterns from molds.
- Verify dimensions of completed patterns, using templates, straightedges, calipers, or protractors.
- Correct patterns to compensate for defects in castings.
- Set up, operate, and adjust a variety of woodworking machines such as bandsaws and lathes to cut and shape sections, parts, and patterns, according to specifications.
- Finish completed products or models with shellac, lacquer, wax, or paint.
- Estimate costs for patternmaking jobs.
- Mark identifying information such as colors or codes on patterns, parts, and templates to indicate assembly methods.
- Repair broken or damaged patterns.
- Maintain pattern records for reference.
- Compute dimensions, areas, volumes, and weights.
- Select lumber to be used for patterns.
- Collect and store patterns and lumber.
- Inventory equipment and supplies, ordering parts and tools as necessary.
- Issue patterns to designated machine operators.
- Construct wooden models, templates, full scale mock-ups, jigs, or molds for shaping parts of products.
- Fit, fasten, and assemble wood parts together to form patterns, models, or sections, using glue, nails, dowels, bolts, and screws.
- Glue fillets along interior angles of patterns.
- Devise or build fixtures or jigs used to hold parts in place during welding, brazing, or soldering.
- Assemble, align, and clamp workpieces into holding fixtures to bond, heat-treat, or solder fabricated metal components.
- Lay out, fit, or connect parts to be bonded, calculating production measurements, as necessary.
- Inspect, measure, or test completed metal workpieces to ensure conformance to specifications, using measuring and testing devices.
- Read blueprints, work orders, or production schedules to determine product or job instructions or specifications.
- Set up, operate, or tend welding machines that join or bond components to fabricate metal products or assemblies.
- Correct problems by adjusting controls or by stopping machines and opening holding devices.
- Give directions to other workers regarding machine set-up and use.
- Select, position, align, and bolt jigs, holding fixtures, guides, or stops onto machines, using measuring instruments and hand tools.
- Mark weld points and positions of components on workpieces, using rules, squares, templates, or scribes.
- Transfer components, metal products, or assemblies, using moving equipment.
- Clean, lubricate, maintain, and adjust equipment to maintain efficient operation, using air hoses, cleaning fluids, and hand tools.
- Prepare metal surfaces or workpieces, using hand-operated equipment, such as grinders, cutters, or drills.
- Conduct trial runs before welding, soldering, or brazing, and make necessary adjustments to equipment.
- Remove completed workpieces or parts from machinery, using hand tools.
- Tend auxiliary equipment used in welding processes.
- Load or feed workpieces into welding machines to join or bond components.
- Observe meters, gauges, or machine operations to ensure that soldering or brazing processes meet specifications.
- Turn and press knobs and buttons or enter operating instructions into computers to adjust and start welding machines.
- Compute and record settings for new work, applying knowledge of metal properties, principles of welding, and shop mathematics.
- Set dials and timing controls to regulate electrical current, gas flow pressure, heating or cooling cycles, or shut-off.
- Record operational information on specified production reports.
- Select torch tips, alloys, flux, coil, tubing, or wire, according to metal types or thicknesses, data charts, or records.
- Fill hoppers and position spouts to direct flow of flux or manually brush flux onto seams of workpieces.
- Start, monitor, and adjust robotic welding production lines.
- Add chemicals or materials to workpieces or machines to facilitate bonding or to cool workpieces.
- Immerse completed workpieces into water or acid baths to cool and clean components.
- Dress electrodes, using tip dressers, files, emery cloths, or dressing wheels.
- Anneal finished workpieces to relieve internal stress.
- Devise or build fixtures or jigs used to hold parts in place during welding, brazing, or soldering.
- Assemble, align, and clamp workpieces into holding fixtures to bond, heat-treat, or solder fabricated metal components.
- Lay out, fit, or connect parts to be bonded, calculating production measurements, as necessary.
- Inspect, clean, and assemble molds before beginning work.
- Release air bubbles and smooth seams, using rollers.
- Spray chopped fiberglass, resins, and catalysts onto prepared molds or dies using pneumatic spray guns with chopper attachments.
- Mix catalysts into resins, and saturate cloth and mats with mixtures, using brushes.
- Check completed products for conformance to specifications and for defects by measuring with rulers or micrometers, by checking them visually, or by tapping them to detect bubbles or dead spots.
- Pat or press layers of saturated mat or cloth into place on molds, using brushes or hands, and smooth out wrinkles and air bubbles with hands or squeegees.
- Select precut fiberglass mats, cloth, and wood-bracing materials as required by projects being assembled.
- Bond wood reinforcing strips to decks and cabin structures of watercraft, using resin-saturated fiberglass.
- Trim excess materials from molds, using hand shears or trimming knives.
- Apply layers of plastic resin to mold surfaces prior to placement of fiberglass mats, repeating layers until products have the desired thicknesses and plastics have jelled.
- Cure materials by letting them set at room temperature, placing them under heat lamps, or baking them in ovens.
- Apply lacquers and waxes to mold surfaces to facilitate assembly and removal of laminated parts.
- Repair or modify damaged or defective glass-fiber parts, checking thicknesses, densities, and contours to ensure a close fit after repair.
- Check all dies, templates, and cutout patterns to be used in the manufacturing process to ensure that they conform to dimensional data, photographs, blueprints, samples, or customer specifications.
- Trim cured materials by sawing them with diamond-impregnated cutoff wheels.
- Mask off mold areas not to be laminated, using cellophane, wax paper, masking tape, or special sprays containing mold-release substances.
- Inspect, clean, and assemble molds before beginning work.
- Fit parts together in pre-assembly to ensure that dimensions are accurate.
- Monitor machine operations to determine whether adjustments are necessary, stopping machines when problems occur.
- Inspect, feel, and measure workpieces to ensure that surfaces and dimensions meet specifications.
- Study blueprints or layouts of metal workpieces to determine grinding procedures, and to plan machine setups and operational sequences.
- Select and mount grinding wheels on machines, according to specifications, using hand tools and applying knowledge of abrasives and grinding procedures.
- Compute numbers, widths, and angles of cutting tools, micrometers, scales, and gauges, and adjust tools to produce specified cuts.
- Turn valves to direct flow of coolant against cutting wheels and workpieces during grinding.
- Set up and operate grinding or polishing machines to grind metal workpieces, such as dies, parts, and tools.
- Dress grinding wheels, according to specifications.
- File or finish surfaces of workpieces, using prescribed hand tools.
- Perform basic maintenance, such as cleaning and lubricating machine parts.
- Remove finished workpieces from machines and place them in boxes or on racks, setting aside pieces that are defective.
- Remove and replace worn or broken machine parts, using hand tools.
- Attach workpieces to grinding machines and form specified sections and repair cracks, using welding or brazing equipment.
- Duplicate workpiece contours, using tracer attachments.
- Inspect dies to detect defects, assess wear, and verify specifications, using micrometers, steel gauge pins, and loupes.
- Place workpieces in electroplating solutions or apply pigments to surfaces of workpieces to highlight ridges and grooves.
- Straighten workpieces and remove dents, using straightening presses and hammers.
- Fit parts together in pre-assembly to ensure that dimensions are accurate.
- Assemble fittings, valves, bowls, plates, disks, impeller shafts, or other parts to prepare equipment for operation.
- Dump, pour, or load specified amounts of refined or unrefined materials into equipment or containers for further processing or storage.
- Operate machines to process materials in compliance with applicable safety, energy, or environmental regulations.
- Monitor material flow or instruments, such as temperature or pressure gauges, indicators, or meters, to ensure optimal processing conditions.
- Turn valves or move controls to admit, drain, separate, filter, clarify, mix, or transfer materials.
- Set up or adjust machine controls to regulate conditions such as material flow, temperature, or pressure.
- Examine samples to verify qualities such as clarity, cleanliness, consistency, dryness, or texture.
- Start agitators, shakers, conveyors, pumps, or centrifuge machines.
- Inspect machines or equipment for hazards, operating efficiency, malfunctions, wear, or leaks.
- Collect samples of materials or products for laboratory analysis.
- Communicate processing instructions to other workers.
- Turn valves to pump sterilizing solutions or rinse water through pipes or equipment or to spray vats with atomizers.
- Maintain logs of instrument readings, test results, or shift production for entry in computer databases.
- Remove clogs, defects, or impurities from machines, tanks, conveyors, screens, or other processing equipment.
- Clean or sterilize tanks, screens, inflow pipes, production areas, or equipment, using hoses, brushes, scrapers, or chemical solutions.
- Measure or weigh materials to be refined, mixed, transferred, stored, or otherwise processed.
- Test samples to determine viscosity, acidity, specific gravity, or degree of concentration, using test equipment such as viscometers, pH meters, or hydrometers.
- Install, maintain, or repair hoses, pumps, filters, or screens to maintain processing equipment, using hand tools.
- Connect pipes between vats and processing equipment.
- Remove full containers from discharge outlets and replace them with empty containers.
- Pack bottles into cartons or crates, using machines.
- Assemble fittings, valves, bowls, plates, disks, impeller shafts, or other parts to prepare equipment for operation.